FreeEMS  0.2.0-SNAPSHOT-285-g028e24c
Files
Data Initialisers

These files provide initial data definitions for items that live in flash. More...

Collaboration diagram for Data Initialisers:

Files

file  flat15PercentAirflow.h
 A dead flat 15% airflow curve to use as a default for untuned Alpha-N engines.
file  DefaultForAlphaN-Load.h
 Default Alpha-N load values spaced evenly.
file  DefaultWith10and20SplitSpacing-Load.h
 Default load values spaced at 10kPa from 20kPa to 100kPa and 20kPa from 100kPa up.
file  DefaultWith400Spacing-RPM.h
 Default RPM values spaced at 400RPM after the cranking and idling rows.
file  Deuces3100-Load.h
 Default load values spaced at 10kPa from 15kPa to 105kPa and 20kPa from 140kPa up.
file  Deuces3100-RPM.h
 Default RPM values spaced at 400RPM after the cranking and idling rows.
file  FredsTruck-Load.h
 The Load axis values for my truck's very rough tune.
file  FredsTruck-RPM.h
 The RPM axis values for my truck's very rough tune.
file  HotelHyundai-Load.h
 A 16 long set of loads for my hyundai before we have tuning software that supports full tables.
file  HotelHyundai-RPM.h
 A default set of RPMs for a typical sohc engine.
file  PetersJSeries-Load.h
 The load axis values for Peter's Honda J Series V6.
file  PetersJSeries-RPM.h
 The RPM axis values for Peter's Honda J Series V6.
file  ScavengersMiata-Load.h
 Hentai's load values spaced at 10kPa from 20kPa to 100kPa and 15kPa from 100kPa up.
file  ScavengersMiata-RPM.h
 Default RPM values spaced at 400RPM after the cranking and idling rows.
file  SeansLT1-RPM.h
 A default set of RPMs for a worked pushrod v8.
file  SimsVolvo-Load.h
 A 16 long set of loads for my truck before mtx supports full tables.
file  SimsVolvo-RPM.h
 A default set of RPMs for a B21A engine.
file  Slater-Load.h
 A 16 long set of loads for the mighty slater!
file  Slater-RPM.h
 A 16 long set of RPMs for the mighty slater!
file  DefaultTiming24RPMx19Load.h
 Default ignition timing data for a mid-90s performance DOHC cylinder head design with square 500cc cylinders.
file  Deuces3100Timing.h
 A fairly standard naturally aspirated 16x16 ignition curve.
file  DeucesS10Timing.h
 DeuceEFI's GM 2200 I4 standard naturally aspirated 13x10 ignition curve for DIS ignition systems.
file  flat0degrees.h
 A flat 0 degree timing table, ONLY for use with mechanical timing as a basis for a trim table or for finding TDC while setting up an engine.
file  flat10degrees.h
 A flat 10 degree timing table, good enough for cranking, and conservative enough for anything powerful, but will bake your exhaust manifold/turbo in minutes if driven on.
file  flat15degrees.h
 A flat 15 degree timing table, good enough for cranking, and conservative enough for anything powerful, but will bake your exhaust manifold/turbo in minutes if driven on.
file  FredsTruckIgnitionTiming.h
 Fred's truck's rough tuned ignition timing table.
file  HotelHyundaiIgnitionTiming.h
 A fairly standard naturally aspirated 16x16 ignition curve.
file  ScavengerTiming24RPMx19Load.h
 Hentai's SD ignition timing, based off of Ben's default.
file  SeansLT1IgnitionTiming.h
 Sean's LT1 rough tuned timing table.
file  SimsVolvoIgnitionTiming.h
 A timing table for a Volvo B21A.
file  SlaterTiming.h
 The slater's rough tuned ignition timing table.
file  TestDIS.h
 A stepped timing test for GM DIS use.
file  DefaultAFR24RPMx19Load.h
 Default petrol AFR data for a mid-90s performance DOHC cylinder head design with square 500cc cylinders.
file  DefaultLambda24RPMx19Load.h
 Default lambda data for a mid-90s performance DOHC cylinder head design with square 500cc cylinders.
file  DeucesS10Lambda.h
 A reasonable default full-range lambda table that suits any engine well enough.
file  GenericLambda.h
 A reasonable default full-range lambda table that suits any engine well enough.
file  HotelHyundaiLambda.h
 The Mighty Hotel's Starion TBI manifold naturally aspirated 16x16 lambda curve.
file  ScavengerLambda24RPMx19Load.h
 Hentai's SD lambda, based off of Ben's default.
file  SimsVolvoLambda.h
 A lambda table for a Volvo B21A.
file  SlaterLambda.h
 The slater's rough tuned lambda table.
file  DefaultVE24RPMx19Load.h
 Default VE data for a mid-90s performance DOHC cylinder head design with square 500cc cylinders.
file  DeucesS10VE.h
 Deuce's GM 2200 I4 engine. Updated 01/12/2013.
file  flat100Percent.h
 A dead flat 100% VE curve to use as a default for typical engines.
file  flat30Percent.h
 A dead flat 30% VE curve to use as a default for typical engines.
file  flat40Percent.h
 A dead flat 40% VE curve to use as a default for typical engines.
file  flat50Percent.h
 A dead flat 50% VE curve to use as a default for typical engines.
file  flat60Percent.h
 A dead flat 60% VE curve to use as a default for typical engines.
file  flat80Percent.h
 A dead flat 80% VE curve to use as a default for typical engines.
file  FredsTruckVE.h
 Will eventually contain my pre-canned tune.
file  HotelHyundaiVE.h
 The Mighty Hotel's Starion TBI manifold naturally aspirated 16x16 VE curve.
file  PetersJSeriesVE.h
 Peter's rough tune on his Honda J Series V6.
file  ScavengerVE24RPMx19Load.h
 Hentai's SD VE, based off of Ben's default.
file  SeansLT1VE.h
 Sean's very very rough IDE-only tune!
file  SimsVolvoVE.h
 A volumetric efficiency table for a Volvo B21A with a B230F intake manifold.
file  SlaterVE.h
 The slater's rough/rich tuned VE table.
file  Bosch.h
 Bosch Coolant/Head / Inlet Air Temperature Transfer Table Data.
file  BoschM12H-2k0Bias.h
 Generated by FreeTherm 0.7-SNAPSHOT using the following parameters:
file  BoschM12H-2k2Bias.h
 Generated by FreeTherm 0.7-SNAPSHOT using the following parameters:
file  BoschM12H-2k49Bias.h
 Generated by FreeTherm 0.7-SNAPSHOT using the following parameters:
file  BoschM12H-2k4Bias.h
 Generated by FreeTherm 0.7-SNAPSHOT using the following parameters:
file  BoschM12H-2k6Bias.h
 Generated by FreeTherm 0.7-SNAPSHOT using the following parameters:
file  BoschM12H-2k7Bias.h
 Generated by FreeTherm 0.7-SNAPSHOT using the following parameters:
file  Denso-2k0Bias.h
 Generated by FreeTherm 0.6 using the following parameters:
file  Denso-2k2Bias.h
 Generated by FreeTherm 0.6 using the following parameters:
file  Denso-2k49Bias.h
 Generated by FreeTherm 0.6 using the following parameters:
file  Denso-2k4Bias.h
 Generated by FreeTherm 0.6 using the following parameters:
file  Denso-2k6Bias.h
 Generated by FreeTherm 0.6 using the following parameters:
file  Denso-2k7Bias.h
 Generated by FreeTherm 0.6 using the following parameters:
file  GM-2k0Bias.h
 Generated by FreeTherm 0.6 using the following parameters:
file  GM-2k2Bias.h
 Generated by FreeTherm 0.6 using the following parameters:
file  GM-2k49Bias.h
 Generated by FreeTherm 0.6 using the following parameters:
file  GM-2k4Bias.h
 Generated by FreeTherm 0.6 using the following parameters:
file  GM-2k6Bias.h
 Generated by FreeTherm 0.6 using the following parameters:
file  GM-2k7Bias.h
 Generated by FreeTherm 0.6 using the following parameters:
file  HondaJSeries-2k4Bias.h
 Generated by FreeTherm 0.7-SNAPSHOT using the following parameters:
file  HotelStarion-2k49Bias.h
 Generated by FreeTherm 0.7-SNAPSHOT using the following parameters:
file  globalConstants.c
 Global constant values.
file  CHTTransferTable.c
 Coolant/Head Temperature Transfer Table.
file  FixedConfig1.c
 First fixed config block.
file  FixedConfig2.c
 Second fixed config block.
file  FuelTables.c
 Fuel VE and Lambda tables.
file  FuelTables2.c
 Fuel VE and Lambda tables.
file  IATTransferTable.c
 Inlet Air Temperature Transfer Table.
file  MAFTransferTable.c
 Mass Air Flow Transfer Table.
file  TestTransferTable.c
 Test data for comms.
file  TimingTables.c
 Injection and ignition timing tables.
file  TimingTables2.c
 Injection and ignition timing tables.
file  TunableConfig.c
 Small tables and other live tunable data.
file  TunableConfig2.c
 Small tables and other live tunable data.

Detailed Description

These files provide initial data definitions for items that live in flash.

Examples: