These files provide initial data definitions for items that live in flash. More...
Collaboration diagram for Data Initialisers:
|
Files | |
| file | flat15PercentAirflow.h |
| A dead flat 15% airflow curve to use as a default for untuned Alpha-N engines. | |
| file | DefaultForAlphaN-Load.h |
| Default Alpha-N load values spaced evenly. | |
| file | DefaultWith10and20SplitSpacing-Load.h |
| Default load values spaced at 10kPa from 20kPa to 100kPa and 20kPa from 100kPa up. | |
| file | DefaultWith400Spacing-RPM.h |
| Default RPM values spaced at 400RPM after the cranking and idling rows. | |
| file | Deuces3100-Load.h |
| Default load values spaced at 10kPa from 15kPa to 105kPa and 20kPa from 140kPa up. | |
| file | Deuces3100-RPM.h |
| Default RPM values spaced at 400RPM after the cranking and idling rows. | |
| file | FredsTruck-Load.h |
| The Load axis values for my truck's very rough tune. | |
| file | FredsTruck-RPM.h |
| The RPM axis values for my truck's very rough tune. | |
| file | HotelHyundai-Load.h |
| A 16 long set of loads for my hyundai before we have tuning software that supports full tables. | |
| file | HotelHyundai-RPM.h |
| A default set of RPMs for a typical sohc engine. | |
| file | PetersJSeries-Load.h |
| The load axis values for Peter's Honda J Series V6. | |
| file | PetersJSeries-RPM.h |
| The RPM axis values for Peter's Honda J Series V6. | |
| file | ScavengersMiata-Load.h |
| Hentai's load values spaced at 10kPa from 20kPa to 100kPa and 15kPa from 100kPa up. | |
| file | ScavengersMiata-RPM.h |
| Default RPM values spaced at 400RPM after the cranking and idling rows. | |
| file | SeansLT1-RPM.h |
| A default set of RPMs for a worked pushrod v8. | |
| file | SimsVolvo-Load.h |
| A 16 long set of loads for my truck before mtx supports full tables. | |
| file | SimsVolvo-RPM.h |
| A default set of RPMs for a B21A engine. | |
| file | Slater-Load.h |
| A 16 long set of loads for the mighty slater! | |
| file | Slater-RPM.h |
| A 16 long set of RPMs for the mighty slater! | |
| file | DefaultTiming24RPMx19Load.h |
| Default ignition timing data for a mid-90s performance DOHC cylinder head design with square 500cc cylinders. | |
| file | Deuces3100Timing.h |
| A fairly standard naturally aspirated 16x16 ignition curve. | |
| file | DeucesS10Timing.h |
| DeuceEFI's GM 2200 I4 standard naturally aspirated 13x10 ignition curve for DIS ignition systems. | |
| file | flat0degrees.h |
| A flat 0 degree timing table, ONLY for use with mechanical timing as a basis for a trim table or for finding TDC while setting up an engine. | |
| file | flat10degrees.h |
| A flat 10 degree timing table, good enough for cranking, and conservative enough for anything powerful, but will bake your exhaust manifold/turbo in minutes if driven on. | |
| file | flat15degrees.h |
| A flat 15 degree timing table, good enough for cranking, and conservative enough for anything powerful, but will bake your exhaust manifold/turbo in minutes if driven on. | |
| file | FredsTruckIgnitionTiming.h |
| Fred's truck's rough tuned ignition timing table. | |
| file | HotelHyundaiIgnitionTiming.h |
| A fairly standard naturally aspirated 16x16 ignition curve. | |
| file | ScavengerTiming24RPMx19Load.h |
| Hentai's SD ignition timing, based off of Ben's default. | |
| file | SeansLT1IgnitionTiming.h |
| Sean's LT1 rough tuned timing table. | |
| file | SimsVolvoIgnitionTiming.h |
| A timing table for a Volvo B21A. | |
| file | SlaterTiming.h |
| The slater's rough tuned ignition timing table. | |
| file | TestDIS.h |
| A stepped timing test for GM DIS use. | |
| file | DefaultAFR24RPMx19Load.h |
| Default petrol AFR data for a mid-90s performance DOHC cylinder head design with square 500cc cylinders. | |
| file | DefaultLambda24RPMx19Load.h |
| Default lambda data for a mid-90s performance DOHC cylinder head design with square 500cc cylinders. | |
| file | DeucesS10Lambda.h |
| A reasonable default full-range lambda table that suits any engine well enough. | |
| file | GenericLambda.h |
| A reasonable default full-range lambda table that suits any engine well enough. | |
| file | HotelHyundaiLambda.h |
| The Mighty Hotel's Starion TBI manifold naturally aspirated 16x16 lambda curve. | |
| file | ScavengerLambda24RPMx19Load.h |
| Hentai's SD lambda, based off of Ben's default. | |
| file | SimsVolvoLambda.h |
| A lambda table for a Volvo B21A. | |
| file | SlaterLambda.h |
| The slater's rough tuned lambda table. | |
| file | DefaultVE24RPMx19Load.h |
| Default VE data for a mid-90s performance DOHC cylinder head design with square 500cc cylinders. | |
| file | DeucesS10VE.h |
| Deuce's GM 2200 I4 engine. Updated 01/12/2013. | |
| file | flat100Percent.h |
| A dead flat 100% VE curve to use as a default for typical engines. | |
| file | flat30Percent.h |
| A dead flat 30% VE curve to use as a default for typical engines. | |
| file | flat40Percent.h |
| A dead flat 40% VE curve to use as a default for typical engines. | |
| file | flat50Percent.h |
| A dead flat 50% VE curve to use as a default for typical engines. | |
| file | flat60Percent.h |
| A dead flat 60% VE curve to use as a default for typical engines. | |
| file | flat80Percent.h |
| A dead flat 80% VE curve to use as a default for typical engines. | |
| file | FredsTruckVE.h |
| Will eventually contain my pre-canned tune. | |
| file | HotelHyundaiVE.h |
| The Mighty Hotel's Starion TBI manifold naturally aspirated 16x16 VE curve. | |
| file | PetersJSeriesVE.h |
| Peter's rough tune on his Honda J Series V6. | |
| file | ScavengerVE24RPMx19Load.h |
| Hentai's SD VE, based off of Ben's default. | |
| file | SeansLT1VE.h |
| Sean's very very rough IDE-only tune! | |
| file | SimsVolvoVE.h |
| A volumetric efficiency table for a Volvo B21A with a B230F intake manifold. | |
| file | SlaterVE.h |
| The slater's rough/rich tuned VE table. | |
| file | Bosch.h |
| Bosch Coolant/Head / Inlet Air Temperature Transfer Table Data. | |
| file | BoschM12H-2k0Bias.h |
| Generated by FreeTherm 0.7-SNAPSHOT using the following parameters: | |
| file | BoschM12H-2k2Bias.h |
| Generated by FreeTherm 0.7-SNAPSHOT using the following parameters: | |
| file | BoschM12H-2k49Bias.h |
| Generated by FreeTherm 0.7-SNAPSHOT using the following parameters: | |
| file | BoschM12H-2k4Bias.h |
| Generated by FreeTherm 0.7-SNAPSHOT using the following parameters: | |
| file | BoschM12H-2k6Bias.h |
| Generated by FreeTherm 0.7-SNAPSHOT using the following parameters: | |
| file | BoschM12H-2k7Bias.h |
| Generated by FreeTherm 0.7-SNAPSHOT using the following parameters: | |
| file | Denso-2k0Bias.h |
| Generated by FreeTherm 0.6 using the following parameters: | |
| file | Denso-2k2Bias.h |
| Generated by FreeTherm 0.6 using the following parameters: | |
| file | Denso-2k49Bias.h |
| Generated by FreeTherm 0.6 using the following parameters: | |
| file | Denso-2k4Bias.h |
| Generated by FreeTherm 0.6 using the following parameters: | |
| file | Denso-2k6Bias.h |
| Generated by FreeTherm 0.6 using the following parameters: | |
| file | Denso-2k7Bias.h |
| Generated by FreeTherm 0.6 using the following parameters: | |
| file | GM-2k0Bias.h |
| Generated by FreeTherm 0.6 using the following parameters: | |
| file | GM-2k2Bias.h |
| Generated by FreeTherm 0.6 using the following parameters: | |
| file | GM-2k49Bias.h |
| Generated by FreeTherm 0.6 using the following parameters: | |
| file | GM-2k4Bias.h |
| Generated by FreeTherm 0.6 using the following parameters: | |
| file | GM-2k6Bias.h |
| Generated by FreeTherm 0.6 using the following parameters: | |
| file | GM-2k7Bias.h |
| Generated by FreeTherm 0.6 using the following parameters: | |
| file | HondaJSeries-2k4Bias.h |
| Generated by FreeTherm 0.7-SNAPSHOT using the following parameters: | |
| file | HotelStarion-2k49Bias.h |
| Generated by FreeTherm 0.7-SNAPSHOT using the following parameters: | |
| file | globalConstants.c |
| Global constant values. | |
| file | CHTTransferTable.c |
| Coolant/Head Temperature Transfer Table. | |
| file | FixedConfig1.c |
| First fixed config block. | |
| file | FixedConfig2.c |
| Second fixed config block. | |
| file | FuelTables.c |
| Fuel VE and Lambda tables. | |
| file | FuelTables2.c |
| Fuel VE and Lambda tables. | |
| file | IATTransferTable.c |
| Inlet Air Temperature Transfer Table. | |
| file | MAFTransferTable.c |
| Mass Air Flow Transfer Table. | |
| file | TestTransferTable.c |
| Test data for comms. | |
| file | TimingTables.c |
| Injection and ignition timing tables. | |
| file | TimingTables2.c |
| Injection and ignition timing tables. | |
| file | TunableConfig.c |
| Small tables and other live tunable data. | |
| file | TunableConfig2.c |
| Small tables and other live tunable data. | |
Detailed Description
These files provide initial data definitions for items that live in flash.
Examples:
- Tables
- Tunables
- Fixed config
- Lookup tables
- Global constants
